And then tap on “Pedometer” icon on APP interface. Please connect your smart bracelet with your phone via Bluetooth in advance, and then open APP “Youth Health”. ![]() Remark: W’hy Bluetooth disconnected and incoming calls and messages do no remind: Support system: IOS 10.0 or above, Android 4.4 or above.Raise hand: Turn on this function, when you lifting hand to tilt the bracelet inward, facing the wearer straight ahead, the bracclc1 automatically bright screen.Remind Mode: It is three modes for you select: Vibration, Bright screen, Bright screen +Vibration.Sedentary and drinking water reminder Turn on this function, set the monitoring period, the bracelet can remind you to drink water or sport at regular intervals during the prescribed time.Do not disturb mode: After you open the “do not disturb mode”, except alarm clock, all notifications in the Settings are not reminded, and the bracelet will no longer have automatic bright screen vibration reminder.Find Device: The bracelet will be vibrate and bright screen.Take a photo: You can use the bracelet to control your phone to take a photo.Heart rate test: Open heart rate detection, set the detection time period, the bracelet can detect the heart rate within the specified time.Notifications Function: Include call notification, SMS notification, application message push such as QQ message push, “WeChat message” push and other functions.Show below: 5.2 “Sport” – Analysis and Report Show below: 5.3 “Device”-settings The following functions can only be realized under the premise that the mobile APP is successful. 5.1 “Home”-Steps, Sleep, Heart, BP, SpO2, Body Temperature These modes need to connect the bracelet to complete the data collection and synchronize to the mobile APP in real time. Theo please connect smart bracelet via Bluetoo1h (Please reference to the Bluetooth Paring Steps) After successful connection between the bracelet and the mobile APP, the movement data will be synchronized automatically. Once the bracelet powers on, you will see a display with the time, date, and other information.After install Youth Health APP, you may required m fill your personal information such as gender, weight etc. The power button is usually located on the side of the bracelet. To turn on a smart bracelet, simply press and hold the power button for a few seconds. Your health steward will begin charging automatically. To charge your health steward smart band, simply connect the charging cable to the band and plug it into a USB port. How To Charge Smart Band Your Health Steward After a few warm ups and tries, you’ll notice that cold fingers do not work well on touch screens. ![]() It is possible that the touchscreen will become faulty if the device becomes too cold or too hot. If the watch is being used outside, keep it at the appropriate temperature. It is critical to ensure that the screen is dust-free and clean. Make sure you’ve pressed and held down the middle button of the SmartBand for at least a few seconds to turn it on. After that, power it up for about 5 minutes to allow it to fully charge. A safety pin or paperclip can be used to poke a small reset button on the back. If you are unable to turn the SmartBand on, you should first try resetting it. Finally, restart your device by opening the Settings app on your phone and following the instructions. ![]() After the band vibrates and a pairing request is displayed on its screen, tap the finish button to complete the pairing. Log in to your Mi account, then connect and pair your phone with the band by following the instructions on the app. You must first download the Mi Smart Band 6 app to begin using it. Select Reset all settings from the Settings menu. Instead of following these steps, you should use your phone’s Mi Band 3 or earlier: open the Mi App. ![]() Under Bluetooth settings, you can reset all settings. Navigate to the Device tab on the main page. Resetting your device connection To reset your device connection, launch the Settings app on your phone. If that doesn’t work, you may need to contact the manufacturer for further assistance. You can try resetting your smartband by holding down the button for 10 seconds. If your smartband still doesn’t work, there may be a problem with the band’s hardware or software. Try charging your smartband for at least 30 minutes to see if that solves the problem. One possibility is that the band is not charged. There are a few reasons why your smartband might not be working.
0 Comments
Leave a Reply. |